Expect to pay $300–$1,200 to mount a TV on a stone fireplace professionally, with about $600 typical according to LatestCost, while Bob Vila puts brick, stone and concrete walls at $200–$800 versus $100–$300 for drywall. The biggest swing factor is what sits behind the stone: thin veneer means anchoring through it into studs or a backer, solid masonry means sleeve anchors or masonry screws into the stone itself.
The full cost breakdown
Most of that range isn't the bracket. It's labor on a hard surface, the over-fireplace setup and getting power to the screen. Here is how the line items stack up, combining GetMediaWall's pricing model with published national figures:
| Line item | Typical cost | Source of figure |
|---|---|---|
| Labor, 65" TV install | $115 | GetMediaWall pricing model |
| Hard-wall (brick/stone) fee | $60 | GetMediaWall pricing model |
| Over-fireplace fee | $55 | GetMediaWall pricing model |
| Flat mount / full-motion mount | $55 / $90 | GetMediaWall pricing model |
| Masonry drilling or setup fee | $50–$200 | LatestCost |
| Irregular fieldstone, slate or granite surcharge | +$100–$400 | LatestCost |
| Surface cable cover | $55 (our model); $20–$80 | GetMediaWall / LatestCost |
| Wire routing behind stone | $140 (our model, accessible cavity); $100–$400+ | GetMediaWall / LatestCost |
| New outlet behind the TV | $165 (our model); $210 avg; $150–$500 | GetMediaWall / Bob Vila / LatestCost |
| Minimum service visit | $105 | GetMediaWall pricing model |
Estimated cost: In our pricing model, a 65" TV on a full-motion mount over a stone fireplace with hidden in-wall wiring comes to $115 + $90 + $55 + $60 + $140 = $460 nationally. Swap to a flat mount with cords showing and it drops to $285. These are our model's estimates, not invoices, and the $140 wiring figure assumes there is a cavity to fish through. Behind solid stone there often isn't one.
For context from the listings themselves: across the 1,009 installers on GetMediaWall, 587 offer TV wall mounting and 166 publish a price. Their median starting price is $99, a drywall-style baseline that stone jobs climb well above. These are the companies' own website claims.
Driver 1: Veneer or solid masonry decides the anchor
Get this wrong and nothing else matters. The three constructions you'll find on an existing fireplace:
| What's behind the face | How to recognize it | What holds the TV |
|---|---|---|
| Adhered stone veneer over cement board / plywood | Stone 1–2 in thick; pilot hole hits a hard board, then hollow or wood | Long lags into studs, or toggles through the plywood + board |
| Anchored brick veneer over wood studs | Full-size brick, roughly 1 in air gap, then sheathing and studs | Lags through a mortar joint, 1.5–2 in into studs |
| Solid brick, block or stone chimney | Dull thud when tapped; drill dust stays masonry the whole depth | Masonry screws or sleeve anchors into the masonry |
Manufactured adhered veneer is thin by design: industry sources put it at about 1–2 inches and, by code, under 15 lb per square foot. MantelMount's tap test is a quick first check: solid brick gives a dull thud, veneer often sounds hollow. The definitive test is one small pilot hole in a spot the TV will cover. A homeowner on Hearth.com did exactly that on a 1989 fireplace: the drill went through 1–1.5 inches of stone, then cement backer, then hollow space. A rod went about 5.5 inches before hitting the chimney. That's a wall where a standard masonry anchor would grip only an inch of decorative stone.
Important: Pine Hall Brick warns that if brick is under 2 inches thick, screws "may punch through to a different material behind it." Never hang a 60–100 lb TV-and-mount load from veneer alone. The load has to reach studs, blocking, a properly fastened backer or solid masonry.
Driver 2: Mortar joint or brick face (pros disagree)
This is the most argued detail in the threads. On a Garage Journal thread about a solid brick fireplace, posters split: one said "Mount in the mortar. Bricks are soft," another preferred mortar because it's easier to patch, and a third said Tapcons "don't hold good at all in mortar." Pine Hall Brick, a brick manufacturer, is unambiguous: drill the brick face, because mortar is softer than fired clay and "can crumble under heavy, sustained loads." It specifies 5/16 x 3 in Tapcon screws, a 1/4 in masonry bit and a hammer drill. MantelMount gives the same advice for stone: fasten into the stone, not brittle grout.
Our read: on solid brick, the brick face holds better and the manufacturer says so. Mortar is the patchable choice if you expect to move the TV. On veneer, the joint is just the doorway. You drill through it so a lag can reach the stud behind, and the joint is easy to repoint afterward.
Rule of thumb: Pick anchors by base material, not by what came in the mount box. Sleeve anchors are the usual choice for brick. The Brick Industry Association notes that hollow cores and partly filled joints can make wedge anchors unsuitable. Distributors say not to swap wedge anchors in for sleeves in hollow brick or block unless that exact anchor is approved for it.
Driver 3: Uneven stone, spacers and plywood backers
Stacked ledgestone and fieldstone rarely give a flat plane. This is where installers add time and where LatestCost's $100–$400 irregular-stone surcharge comes from. Options that real homeowners and pros report:
- Spacers on the bolts. A Fine Homebuilding poster slips tubing over toggle bolts as shims and paints it to match the mount. MantelMount suggests hanger bolts with nuts to set depth.
- A surface plywood "spreader." On DIYnot, posters with a thin chimney wall bolted a thick ply panel to the masonry away from the flue (a manufacturer helpline told one of them 38 mm, about 1-1/2 in), then hung the bracket on the panel. You can stain or face it so it reads as a deliberate panel.
- A backer built in from the start. One TigerDroppings builder framed a stud-depth inset backed with 3/4 in plywood, then ran power and Cat6A inside it. That only works before the stone goes up, or as a stone-removal rebuild.
Pro tip: If your veneer sits over plywood and cement board, the Fine Homebuilding advice is long heavy-duty toggles through both, snugged but not overtightened. Too much torque cracks thin stone.
Driver 4: Getting power and HDMI to the screen
Only two of the six forum threads we read (Garage Journal, Fine Homebuilding, TigerDroppings, Hearth.com, DIYnot, Hometalk; all listed in Sources) dealt with wiring at all, and both treated it as the hardest part. The NEC is clear on one thing: flexible cords, including the TV's own power cord, may not run through or be concealed inside walls (NEC 400.12). Listed in-wall kits from Wiremold and Legrand get around this by using NM cable inside the wall, with the flexible cord staying outside.
Behind solid stone there's usually no cavity to fish through. That leaves a painted surface raceway, cables dropped from the ceiling or attic, routing down the side of the chimney into a stud bay, or core-drilling the masonry. Our model's $165 "new outlet behind TV" assumes a reachable stud bay. Expect the $150–$500 end of LatestCost's range, or more, when the electrician has to work around masonry. Our cable concealment page explains what that service covers.
Important: A new receptacle above a fireplace is permanent wiring. Have a licensed electrician add it, and don't feed an in-wall kit from an extension cord, which forum electricians flag as a 400.12(1) problem.
Budget vs mid-range vs high-end
Price range: Budget, about $285–$400. Solid brick, flat mount, cords in a painted surface raceway. Our model's $285 plus a cover, comparable to LatestCost's low end.
Price range: Mid-range, about $460–$600. Full-motion mount, in-wall wiring where a cavity exists or a new outlet, veneer anchored into studs. Our model's $460–$485, up to LatestCost's $600 typical.
Price range: High-end, $800–$1,200+. Pull-down mount to fix viewing height, irregular fieldstone (+$100–$400), an electrician-run outlet ($150–$500), plywood spreader panel. If you want the TV recessed into the stone, you're pricing a rebuild. Our model puts a 16+ ft stone-finish wall with a 72" fireplace at $11,900–$17,500 nationally.
Pull-down mounts come up because height is the other recurring complaint: four of the six threads raised it, from "looking up at it" to "such a crick in the neck." A Garage Journal poster in 2019 chose a $109 Monoprice pull-down over a $299 MantelMount. See our pull-down mount breakdown and the TV height guide before you drill. Heat came up in three of the six threads, so check temperatures with the fire running.
Where to save (and where not to)
When to DIY: You've confirmed solid brick or block, you own or can rent a hammer drill, and it's a flat or tilt mount. The tools and anchors are cheap. The work is careful measuring, since every wrong hole is permanent.
When NOT to DIY: Your pilot hole finds a hollow cavity, the face is natural fieldstone, there's a gas insert below, or you need a new outlet. A cracked stone or a lag that misses the stud costs far more than the $60 hard-wall fee in our model.
Save by bringing your own mount (our model charges $0 for the mount line in that case) and by accepting a surface raceway instead of chasing masonry. Don't save on anchors or skip the pilot-hole test. Across GetMediaWall's listings, 122 installers name stone and 177 name brick among the wall types they handle. Only 223 of 1,009 claim insurance and 84 state a warranty (median 12 months), so ask about both. Compare local installers who list stone work, or get free quotes and mention the fireplace type up front.
Cost FAQ
Is mounting on stone more expensive than drywall? Yes. Bob Vila's figures are $200–$800 for masonry versus $100–$300 for drywall. Our model adds a $60 hard-wall fee and a $55 over-fireplace fee.
Can veneer hold a TV by itself? No. Anchor through it into studs, a fastened plywood/cement-board backer or the masonry behind it.
Does hiding wires behind stone always cost extra? Usually. With no cavity, expect $100–$400+ for routing, or use a $20–$80 surface cover.
Sources
- LatestCost: Cost to Mount a TV on a Stone Fireplace — $300–$1,200 range, ~$600 typical, drilling fees, irregular-stone surcharge, wire routing, outlet costs
- Bob Vila: TV Mount Installation Cost — $200–$800 masonry vs $100–$300 drywall, $210 average outlet, in-wall wiring up to $1,000
- Pine Hall Brick: Drill Into the Brick, Not the Mortar — brick-face vs mortar guidance, Tapcon size, under-2-in veneer punch-through warning
- MantelMount: Mounting Your TV on Brick or Stone — tap test, veneer has studs behind, avoid grout
- MantelMount: How to Mount a TV on an Uneven Stone Wall — hanger bolts and nuts for depth, sleeve/masonry anchors for real stone
- Mount-It: Best TV Mount for Stone Fireplace — lags through veneer, 1.5–2 in into studs
- Eldorado Stone FAQ — adhered veneer weight under the 15 lb/sq ft limit
- BNP Media: Advances in Manufactured Masonry Thin Veneers — thin veneer about 1–2 in thick
- IIBEC Technical Advisory 001-2021 — 1 in air space behind brick veneer on wood studs
- Brick Industry Association Technical Note 44 — sleeve vs wedge anchors in brick masonry
- Confast: Can Wedge Anchors Be Used in Other Base Materials? — wedge anchors need solid base material
- Wiremold CMK70 FAQ — flexible cord in wall is an NEC violation; kits use NM cable
- EC&M: Through-the-Wall Cord Connection — NEC 400.12 restrictions
- Mike Holt Forum: Legrand In-Wall Outlet Relocation Kit — extension-cord-fed kits and 400.12(1)
- Garage Journal: TV Mount Over Brick Fireplace — mortar vs brick debate, anchors, heat, wiring, pull-down mount prices (thread read)
- Fine Homebuilding: TV Mounting on Stone Fireplace — toggles through plywood and Durock, tubing spacers (thread read)
- TigerDroppings: Mounting TV Over Fireplace With Stone Facade — hammer drill tips, 3/4 in plywood inset with power and Cat6A (thread read)
- Hearth.com: Mounting a TV Above Mantel — pilot hole found stone, cement backer, hollow space (thread read)
- DIYnot: TV Mount on Chimney Breast — plywood spreader, 38 mm ply, heat concerns (thread read)
- Hometalk: Mount Stacked Stone to Fireplace Wall and Mount TV — viewing-angle regret (thread read)