GetMediaWall

Guide

IKEA Hack Media Wall: BESTA, HAVSTA & BILLY Built-Ins That Hold Up

IKEA hack media wall builds cost about $1,000 vs $3,200–$7,000 quotes. 10 rules for BESTA, HAVSTA and BILLY: TV fit, sag, plinths, fillers and wall anchoring.

9 min read1,888 wordsNov 14, 2026

An IKEA hack media wall works, and builders who wrote up their projects spent roughly $950–$1,100 against contractor quotes of $3,200–$7,000. The catch: the cabinets are only the skeleton. A continuous top, fillers, a raised plinth and trim are what make BESTÅ, HAVSTA, BILLY or stock kitchen boxes read as built-in. And the TV has to hang on studs, not on the furniture.

Below are the ten decisions that separate a convincing hack from flat-pack with crown molding glued on. They're drawn from IKEA's own spec sheets, six published builds and the owner complaints that keep coming up.

1. Choose the carcass by depth and wall rules, not by looks

Each IKEA line comes with its own limits, and those limits decide where it can go in a media wall. Here are the published specs side by side:

CarcassDepthBody materialRated loadWall-hang allowed?
BESTÅ frame (64 cm / 38 cm tall)15 3/4" or 7 7/8"Particleboard20 kg (44 lb) per surface on floorYes, with suspension rail
BESTÅ frame (128 / 192 cm tall)15 3/4"Particleboard20 kg (44 lb) per surfaceNo, floor only
BESTÅ TV bench15 3/4"ParticleboardTV max 16 kg (35 lb) on some modelsRail must not be used
HAVSTA cabinet / TV unit14 5/8" or 18 1/2"Solid pine51–99 lb per shelf; TV unit top 110 lbNo, floor only, anchored
BILLY bookcase 31 1/2"11"Particleboard, fiberboard back66 lb per shelfNo, floor only, anchored
Stock kitchen wall cabinetAbout 12"VariesNot rated as a floor baseNeeds a built platform

Best for: BESTÅ suits the low credenza run under the TV. BILLY is the cheapest way to get tall flanking bookcases. HAVSTA costs more, but its solid pine takes paint and abuse better, and its 18 1/2" units have to go at the bottom of any stack.

2. Size the TV opening before you buy a single box

A 16:9 screen is about 0.87 times its diagonal in width. That puts a 65" TV around 56.7" wide, a 75" around 65.4" and an 85" around 74.1". The common 180 cm BESTÅ bench is only 70 7/8" wide, so an 85" TV overhangs it. If you add tall BILLY towers at each end, the screen ends up jammed between them.

Rule of thumb: Pick the TV you'll own in five years, add a few inches of breathing room on each side, and design the center bay to that number.

3. Hang the TV on the wall, never on the cabinet

This is the most common structural mistake. IKEA rates some 120 cm BESTÅ TV benches for a TV of no more than 16 kg (35 lb). The same listing says the BESTÅ suspension rail must not be used with TV benches. The backs of BILLY and BESTÅ are thin fiberboard. Put the TV mount on studs (or masonry anchors) and build the cabinet around it.

Estimated cost: GetMediaWall's pricing model puts a pro mount of a 75" TV at $140 for the install, plus $55 for a flat mount and $165 for a new outlet behind the screen. That's about $360, and the cabinet work stays DIY. Across the 587 installers listed on GetMediaWall for TV wall mounting, 166 publish prices, with a median starting price of $99 (their own website claims).

4. Anchor every box into studs, then check the bracket spacing

IKEA marks BILLY with a tip-over warning, and HAVSTA units must be fastened with the included wall fastener. HAVSTA also must not be hung on a wall. Owners keep reporting that BESTÅ's brackets don't line up with 16" stud spacing. The fix is to screw a 1x ledger or the suspension rail into the studs and fasten the cabinets to that. The 82" BESTÅ build below used helical drywall anchors through the cabinets' wall points. Treat that as a minimum, not a model. Our guide to attaching a media wall frame to drywall, brick or plaster covers fixings by wall type.

Important: Wall-hung BESTÅ capacity "depends on the wall material," per IKEA's support page. No single number holds for every wall. On plaster, metal stud or hollow block, have a pro pick the fixings.

5. Raise everything on a plinth so the baseboard disappears

Built-ins sit on a toe-kick, and furniture sits on feet. Builders handled this in different ways:

  • One BILLY builder says to raise the cases 2–3" from the start, because otherwise the baseboard leaves a lip at the bottom shelf.
  • A Lowe's-cabinet build used 1x6 platforms to lift the boxes 6". The builder later said 1x4s would have been enough.
  • The 82" BESTÅ wall used 1x6 MDF, 5 1/2" actual, to sit a 1/4" proud of the room's 5 1/4" baseboard.

Stock kitchen wall cabinets have no toe-kick at all, so they need this platform.

6. Cap the run with one continuous top

Separate cabinet tops leave a seam at every box. The 82" BESTÅ builder laminated two layers of 3/4" MDF into a 1 1/2" top and had it cut at Home Depot. A 114" nook build used two 1.5" spruce panels cut free at Lowe's to 56.5" x 20". Those panels overhang about 1.5" in front and about 5" at the back to clear the wall. Screw the top up from inside the cabinets so no fasteners show.

Pro tip: If you leave a deeper overhang at the back, you get a cable chase along the wall without cutting the cabinet backs.

7. Fill every gap. Fillers do most of the "custom" work

Walls aren't square, and IKEA widths rarely match your alcove. Builders filled the gaps with:

  • 3/8" x 3" poplar strips between BILLY cases
  • 1x2 MDF face frames, joined with biscuits
  • wainscoting sheet jigsawed to fill end gaps
  • 1/4" plywood over exposed cabinet sides

One blogger who skipped this step said the wall-to-wall result looked like "a poorly-fitted suit," with gaps everywhere.

Pro tip: Use paintable caulk. One builder had to strip and redo every seam after buying the wrong tube. Prime the IKEA foil with a strong bonding primer before you paint.

8. Plan for sag before you load the shelves

BILLY is rated at 66 lb per 31 1/2" shelf, and BESTÅ at 20 kg (44 lb) per surface. Owners still report droop on the wider spans. One Reddit owner says the 70 7/8" BESTÅ bench bows under a medium-to-large TV unless you add the center support leg. In the 82" build, a shelf bridge over the TV sagged about 1/4" until the builder added L-brackets. On a homeschooling forum's BILLY thread, owners say the wide units droop while the narrow ones don't.

Best for: Heavy books, records and AV gear should go in narrow bays or on shelves stiffened with a hardwood front lip. More fixes are in our built-in bookshelf sag guide.

9. Ventilate closed doors and leave power to an electrician

Closed doors trap heat. One Reddit builder's BESTÅ console overheated until they routed vent cutouts and added two small fans. Another owner leaves the back panel off entirely for exhaust. Plan cable grommets and rear cutouts before you paint.

Important: Moving or adding an outlet behind the TV or inside the cabinet run is electrical work. In many US jurisdictions it needs a licensed electrician and possibly a permit. Don't run extension cords through the wall. A recessed power-and-cable kit or a pro cable-concealment install is the safe route.

10. Know what the hack actually saves

Here are the published builds that gave both a DIY total and a pro quote:

BuildDIY totalPro quote / estimate
82" TV BESTÅ wall with bridge and crown~$1,100$5,000–$7,000
Lowe's wall-cabinet media center~$1,100$5,500
114" BESTÅ credenza nookunder $950$3,000–$4,000
IKEA living-room media wall~$1,000$3,200

GetMediaWall's pricing model puts a professionally built 8–12 ft painted built-in wall unit at $5,100–$7,500 nationally, and $6,600–$9,800 in the Bay Area. Few companies publish prices for this work. Of the 25 custom built-in companies listed on GetMediaWall, only 3 publish a starting price. Their median is $8,400, and that's the companies' own claim from a tiny sample. The DIY savings are real, but they cost time: the two BESTÅ builders logged about 25 and 30 hours, plus repeat store trips because IKEA stock ran out.

When NOT to DIY: If you don't own (or can't borrow) a miter saw and brad nailer, or the wall is plaster, metal stud or out of plumb, the trim becomes the hard part. For a side-by-side comparison, read media wall kit vs custom build. Or get matched with local installers for quotes on just the parts you'd rather hand off.

The quick verdict

If you only do one thing right, mount the TV to studs before any cabinet goes in, and size the center bay to the TV you'll buy next. After that, the cheap stuff does the convincing: a continuous top, a plinth and fillers. Want a pro for only the mount and power? Compare installers near you.

Sources

Keep reading

Ready to Start?

Turn Inspiration Into Reality

Connect with media wall installers and get free quotes for your project.