Yes, a pull down TV mount over a fireplace is worth it if your TV sits high enough to strain your neck and your mantel projects no more than 18 inches (12–15 inches if you recess the mount). Manual models like the MantelMount MM340 lower a 20–90 lb TV up to 27 inches, but mantel depth, wall type, cable slack and spring tension decide whether it actually works.
Phase 1: Prove the mount physically fits
A pull-down mount swings out and down in an arc, and a deep mantel gets in the way. Do this phase first: it can rule the mount out before you drill. MantelMount's manuals give a fit test. Measure:
- Wall space height: from the top of the mantel to the ceiling or crown molding
- TV height: the full height of the TV, plus the soundbar if it hangs below the TV
- Mantel depth: how far the mantel sticks out from the finished wall
Then add the clearance from the manufacturer's chart. For a surface-mounted MM340 it is TV height + 4 inches for a mantel under 9 inches deep, +5 inches for 9–11 inches, +6 inches for 11–14 inches and +8 inches for 14–18 inches. Past 18 inches, that model can't clear the mantel.
Important: Every pull-down mount has its own clearance chart. Use the installation guide for the exact model you're buying.
Phase 1 mini-checklist:
- Wall space height ≥ TV height + chart clearance
- Mantel depth measured to the nearest half inch, trim included
- Soundbar height included if it hangs below the TV
- Combined TV + soundbar weight written down
Phase 2: Match the mount to the TV and the mantel
Most buyers check the maximum weight and miss the minimum. Pull-down mounts counterbalance the TV with a gas spring or tension mechanism. If the TV is lighter than the bottom of the range, the spring wins. Mount-It reviewers report a TV that wouldn't stay down even at minimum tension. A pro installer who wrote up his first MM720 install says the first setting snapped the TV back against the wall.
Compiled from MantelMount's spec sheets and manuals and Mount-It retail listings:
| Mount | TV weight | Screen size | Max drop | Max mantel depth | Stud spacing |
|---|---|---|---|---|---|
| MantelMount MM340 (surface) | 20–90 lb | 44–80 in | 27 in | 18 in | up to 28 in |
| MantelMount MM340 + RB100 recess box | 20–90 lb | 44–80 in | 27 in | 15 in | 16 in (wider needs extenders) |
| MantelMount MM540 + RB100 (adds up to 9° tilt) | 20–90 lb | 44–80 in | 27 in | 15 in | 16 in |
| MantelMount MM700 + RB100 | 30–115 lb | 50–90 in | 24 in | 12 in | 16 in |
| MantelMount MM860 (motorized) | under 125 lb | over 50 in | per manual | 19 in recessed / 22 in surface | 2+ wood studs |
| Mount-It MI-384L | 75–110 lb | 65–85 in | 25.8 in adjustment | not listed | not listed |
Recessed, the MM700 allows only a 12-inch mantel, so a big TV on a deep stone mantel can pass the weight check and fail the fit check.
Phase 2 mini-checklist:
- TV + soundbar weight falls inside the range, not just under the max
- Soundbar bracket confirmed (the MM340 needs a separate accessory)
- Max mantel depth for your chosen configuration (surface vs recessed) checked against Phase 1
Phase 3: Check what the wall is made of
The levered arm puts more load on the wall than a flat mount does. MantelMount's manuals call for wood studs and drywall no thicker than 5/8 inch. For brick or stone, the MM340 manual allows the included concrete anchors only if the masonry is structurally sound, several inches thick, and can hold four times the weight of the TV and mount. It recommends a masonry pro for that job. On a Bob Is The Oil Guy forum thread about these mounts, one poster warned that sheet-metal studs won't hold a loaded, extended arm without reinforcement.
The wall types listed by the 1,009 installers on GetMediaWall bear this out. 177 say they work on brick and 122 on stone, but only 64 list "fireplace" as a wall type and just 18 mention metal studs (these are the companies' own website claims). If your chimney breast is masonry or steel-framed, ask about that wall type specifically before you book.
Phase 3 mini-checklist:
- Stud material confirmed (wood, metal, or masonry)
- Stud spacing measured at mount height
- Drywall ≤5/8 in thick
- Masonry: soundness and thickness confirmed by a pro
Phase 4: Plan power and cable slack for the full drop
On a pull-down, cables have to reach in both positions and through the swivel. The MM340 manual has you tie them along the lifting arm. A Tom's Guide forum owner of a different pull-down cut an extra drywall opening so cords stayed hidden up or down. A poster in the BITOG thread noted that anything parked behind the TV, like a router, has to survive the TV moving daily.
Rule of thumb: Make every cable loop longer than the mount's maximum drop (27 inches on an MM340), then add extra for the swivel. Test the full travel with the TV unplugged first. A cable that goes tight at the bottom will eventually damage an HDMI port.
Important: A TV's power cord can't simply be fed through the wall. NEC 400.12 bars flexible cords from being concealed in walls. Use a listed in-wall power kit or have a licensed electrician add a receptacle. Our in-wall outlet code guide covers the options. The MM860 motorized mount also needs power for its motor; its manual says hard-wiring it requires a licensed electrician.
Phase 4 mini-checklist:
- Outlet location doesn't block the wall plates (the MM440 manual has you relocate the outlet or shift the plates)
- Cable loop ≥ max drop + swivel allowance
- Code-compliant power path (kit or new receptacle)
- No router or streaming box placed where the arm will crush it
Phase 5: Decide whether to recess it
A recess box like MantelMount's RB100 sinks the lifting mechanism into the wall, so the TV sits about 1.75 inches off the wall when it's raised. The cutout MantelMount quotes is about 28.2 in tall, 7.4 in wide and 3.7 in deep. That's a trade-off: you get the flush look but give up mantel depth (18 → 15 in on the MM340) and need tighter stud spacing.
Important: The RB100 guide tells you to cut a small "spy window" first, check for fireplace components behind the wall, and cut a center stud only if it is non-bearing. Over a gas fireplace or a built-in electric insert, have a fireplace pro look inside before you cut. If you're building a new media wall, frame the recess opening from the start. Our recessed TV guide covers framing and ventilation.
Phase 5 mini-checklist:
- Mantel depth still within the recessed limit
- Spy window cut and cavity inspected
- Center stud bearing status confirmed before cutting
- Recess framed in at build stage if the wall is new
Phase 6: Install, balance and set the stops
Set spring tension after the TV is hung, until it stays where you leave it and returns gently. Then set the bottom stops so the TV and arm can't come down onto the mantel. The MM340 manual warns that removing the stops for extra travel can make the lifting arm hit the mantel. Then check heat: the MM860 manual limits the mount to decorative fireplaces that aren't the home's main heat source, and says the front edge of the mantel should never exceed 110°F. The Tom's Guide owner taped a meat-thermometer probe under their mount, set an alarm at 110°F, and saw about 90°F in use. AVS Forum members warn that a lowered TV sits closer to a running fire. Our heat and ventilation rules apply doubly here.
Phase 6 mini-checklist:
- Tension adjusted with the final TV and soundbar attached
- Bottom stops set so nothing touches the mantel
- Mantel-edge temperature checked with the fire on high
- Kids told not to pull on it (every manual warns this)
Decision points
Rule of thumb: If your mantel is deeper than 18 inches, most manual pull-downs are out. Look at mounts with longer reach, or move the TV instead. The TV height guide shows when relocating beats retrofitting.
Rule of thumb: If TV plus soundbar sits within a few pounds of either end of the weight range, pick the next model. Balancing is hardest at the edges.
Rule of thumb: Choose motorized only if someone in the house won't pull a handle. The installer who wrote up his MM720 job says the automated version costs about three times as much as the manual one. A Tom's Guide commenter noted people get "too lazy" to lower a manual mount.
Rule of thumb: If the bracket would bother you when the TV is down, go recessed or skip it. That was the top complaint in a Slickdeals thread on these mounts: "you can see the wall mount."
What a pro install adds up to: one worked example
Take a 65-inch TV moving onto a pull-down mount over a 10-inch-deep wood mantel, with a new outlet behind the TV. GetMediaWall's pricing model has no pull-down line item, so treat this as a floor rather than a quote:
| Line item (our estimate model) | Cost |
|---|---|
| Install, 65-inch TV | $115 |
| Over-fireplace fee | $55 |
| Mount (customer supplies the pull-down) | $0 |
| New outlet behind TV | $165 |
| Labor subtotal | $335 |
| Add if brick or stone | +$60 |
Estimated cost: Roughly $335–$395 in labor plus the mount itself. In the 2020 Slickdeals thread, MantelMount list prices were $229 (MM340), $399 (MM540) and $549 (MM700). Mount-It's MI-384L listed at $249.99 at CDW.
Few installers publish prices. Of the 587 TV-mounting companies listed on GetMediaWall, 166 post a starting price, with a median of $99. Of the 125 offering fireplace media walls, only 19 do, with a median starting price of $189. Those are companies' own advertised starting points, not final bills, so ask whether a quote covers balancing and recessing. To get quotes based on your wall, answer a few questions for free quotes or compare local installers. If the outlet and in-wall wiring are the hard part, see in-wall cable concealment.
Your full pre-build checklist
- Wall space height ≥ TV height + the manufacturer's clearance for your mantel depth
- Mantel depth within the limit for surface or recessed configuration
- TV + soundbar weight inside the range, not near the minimum
- Soundbar bracket compatible (and counted in TV height)
- Wood studs confirmed, spacing measured. Masonry or metal studs reviewed by a pro
- Cable loops longer than the full drop plus swivel; travel tested unplugged
- Code-compliant power: listed in-wall kit or a new receptacle by a licensed electrician
- Spy window inspected before any recess cut over a fireplace
- Bottom stops set; spring tension balanced with final load
- Mantel-edge temperature under 110°F with the fire running
If you're planning a new fireplace media wall rather than retrofitting, build the recess, outlet and conduit in from day one. That's far cheaper than cutting into a finished wall later.
Sources
- MantelMount MM340 installation manual (PDF) — 20–90 lb, 44–80 in, 18 in max mantel, 28 in stud spacing, clearance chart, masonry anchor rule, bottom-stop warning
- MantelMount specifications with RB100 recess box (PDF) — 27/24 in drop, 15/12 in mantel limits, 16 in stud spacing, 1.75 in depth, recessed clearance chart
- MantelMount MM860 manual (PDF) — decorative-fireplace limit, 110°F mantel edge, 19/22 in mantel limit, 125 lb, wood studs, electrician for hard-wiring
- MantelMount MM440 manual (PDF) — outlet relocation and cable tie routing
- MantelMount RB100 installation guide (PDF) — spy window, non-bearing center stud, fireplace component warning
- MantelMount RB100 product page — 28.2 x 7.4 x 3.7 in cutout
- Mount-It MI-384L at B&H — 75–110 lb, 65–85 in, 25.8 in adjustment
- Mount-It MI-384L at CDW — $249.99 listing
- Mount-It 65–85 in pull-down product page and reviews — reviewer reports of TV not staying down
- Slickdeals: MantelMount above fireplace TV mounts — 2020 list prices, visible-bracket complaints
- Tom's Guide forum: TV mounting on top of fireplace — 90°F measurement with 110°F alarm, extra drywall hole for cords, "too lazy" comment
- Bob Is The Oil Guy: Above fireplace pull-down TV mounts — metal stud warning, router behind TV
- AVS Forum: My TV must go above this fireplace? — heat concern when lowered
- ResTech Today: Tackling my first MantelMount MM720 install — gas spring snap-back, wall-plate recalculation, motorized ≈3x cost
- EC&M Code Q&A: Where can you not use flexible cords? — NEC 400.12 concealment rule