Yes, a projector screen in a media wall can drop in front of your everyday TV. It works if the fabric hangs at least 4 inches past the TV's front face, the screen is tab-tensioned so it stays flat, and the housing, projector power and 12V trigger wiring go in before drywall. Then you get a 65-inch TV for weekdays and a 120-inch picture for movie night.
We read five forum threads where homeowners tried this (AVForums, What Hi-Fi, HiFiVision, Stereonet). The same three problems kept coming up: the screen hitting the TV, the fabric waving, and the picture landing at the wrong height. All three are decided at the framing stage.
The clearance problem nobody measures until the screen hits the TV
A roll-down screen hangs straight down from its housing. If the housing sits flush against the wall, the fabric drops onto the TV, the soundbar and anything else that sticks out. Three of the five threads we read started with exactly this question. One AVForums planner worked out they needed a 19 cm (about 7.5 inch) gap between the wall and the fabric to clear their set. A replier said "100mm or more" off the wall is usually enough. On HiFiVision, one owner's ceiling screen hung about 12 inches from the wall and roughly 4 inches in front of the TV.
Another poster there sized an L-bracket only a quarter to half an inch beyond the TV's depth, which is too thin for a living room. The same thread describes ceiling screens with no wall behind them swaying when a fan or AC vent blows on them. Here is the rule we would use: measure from the finished wall to the most forward point of the TV, soundbar or mantel ledge, then add at least 4 inches. That is your minimum wall-to-fabric distance.
How the screen rolls matters too. An AVForums contributor pointed out that "roll-under" screens drop the fabric close to the wall and "reverse roll" screens push it further out. Even reverse-roll models fell short of the 19 cm that one homeowner needed, so spacer blocking was needed. If your TV sits on a full-motion arm (see our guide to recessed arms vs. surface swivels), measure it fully retracted. Retract it before every screening.
Where the screen housing lives: four ways to hide it
Four of the five threads ended up with the screen fixed in or to the ceiling rather than on the wall. The ceiling is the only place a 9-to-11-foot housing can disappear:
| Mounting approach | How it clears the TV | When it must be decided | Visible with screen up | Main trap reported |
|---|---|---|---|---|
| Wall brackets / L-brackets | Brackets stand the case off the wall | Any time | Whole case | Thin clearance margins; case is an eyesore |
| Ceiling surface mount | Case hung forward of the wall | Any time | Whole case on ceiling | Fabric sways from fans and HVAC |
| Pelmet / bulkhead box | Case hidden in a soffit at the top of the media wall | During the build | Painted soffit only | Soffit depth must match the clearance you calculated |
| In-ceiling recessed housing | Fabric drops through a slot or trap door | Before drywall or ceiling finish | Narrow slot or flush door | Joist direction, service access, power in the void |
The pelmet route suits UK-style media walls, which already have a deep stud or MDF frame. Extend it into a bulkhead and drop the screen out of its underside, as one AVForums homeowner planned. The fully recessed route looks cleanest, but it is real carpentry. Another AVForums member found the joists ran parallel to the wall, cut a screen-width opening, and hung the case from timbers fixed across the joists, which meant lifting part of the floor above. In-ceiling models such as Elite Screens' Evanesce Tab-Tension B are sold for both above-ceiling and below-ceiling access installation and include brackets to suspend the case from the structure overhead. Draper's Access installation manual is explicit that the entire bottom of the case must stay unobstructed so the roller and screen can be serviced. Never drywall the housing in solid.
Important: Most recessed screens plug in with a short cord; Elite lists 98.4 inches for the Evanesce B. Do not run an extension cord through the ceiling to reach it. NEC 400.12 bars flexible cords from being run through holes in walls and ceilings, concealed in them, or used in place of fixed wiring. Have a licensed electrician add a receptacle or junction box inside the recess cavity, in the same visit as any outlet behind the TV.
Flat fabric, the right height, and the black drop
The second recurring complaint was waves. On AVForums, one owner's manual Da-Lite screen developed a wave at both sides that showed on bright scenes. Another reported minor edge curl. Three of the five threads raised flatness or flutter. The fix that kept coming up is a tab-tensioned screen, which uses side cables and tabs to pull the fabric taut. Elite Screens' own guidance on ultra-short-throw (UST) projectors is blunter. Because UST light strikes the screen at a steep angle, non-tensioned material "may exhibit minor wave or curls." For UST projectors Elite recommends only a fixed-frame screen or a tab-tension screen.
Height is the third trap, and the math is simple. A 120-inch 16:9 screen has an image about 104.6 inches wide and 58.8 inches tall. In an 8-foot (96-inch) ceiling with a flush recessed housing, the bottom of the image lands about 37 inches off the floor, before any top border. With a 10-foot ceiling the same screen's picture bottoms out around 61 inches, which is far too high for a sofa. That gap is filled by black drop, the extra black border above the image. One AVForums owner had to add an extension because the screen's top border was too short. A HiFiVision installer recommended a custom extra-masking order for tall ceilings. Elite warns that the top border on its Evanesce B is already set to its full extent and must not be increased. So order the drop length for your ceiling height. You can't fix it later.
Rule of thumb: Pick the screen size so its image fully covers the TV and the speaker grilles you don't want lit. A 65-inch TV is roughly 57 by 32 inches, so 100 to 120 inches of 16:9 screen covers it with room to spare.
Placing the projector: throw distance and the wiring run
Throw distance comes from one formula: distance = throw ratio × image width. For a 120-inch 16:9 screen (about 104.6 inches wide) and a projector with a 1.5:1 ratio, that is about 156 inches, or 13 feet from lens to screen. Common long-throw ratios of 1.5 to 2.0 put a 120-inch image roughly 12 to 18 feet back. In many living rooms that is behind or directly above the sofa, so check where the ceiling joists, lights and fans are before you buy. A zoom lens gives a range rather than one point; settle the mount location from the maker's calculator before the ceiling is opened.
UST projectors sit inches from the wall, usually on the console below the TV. That keeps the wiring inside the media wall but brings back the strict screen-flatness requirement above. A ceiling-mounted long-throw projector needs three runs from the media wall's equipment area: an HDMI cable (or conduit to pull one later), a power receptacle at the mount, and a low-voltage 12V trigger cable. The trigger lowers the screen automatically when the projector or receiver powers on. Elite's in-ceiling screens and the What Hi-Fi build we read both use one. Run conduit to the projector position even if you buy the projector next year. Our conduit and HDMI future-proofing guide explains sizing.
Pro tip: The What Hi-Fi owner whose screen dropped through a plasterboard slot also suggested pre-running a USB lead for firmware updates and a second mains feed while the ceiling is open.
What the combo costs, and who builds it
As a worked example, GetMediaWall's pricing model puts an 8–12 ft painted media wall at $3,000–$4,400 nationally ($3,900–$5,700 in the San Francisco Bay Area). Mounting a 56–65 inch TV flat with cords showing is estimated at $150–$200. Adding a new outlet behind the TV is a $165 option in the same model. Those are our estimates, not invoices.
Estimated cost: Across the 1,009 installers listed on GetMediaWall, 113 say they offer projector screen installation. Only 2 of them publish a price, with starting prices from $479 and a median of $538. Treat that as a floor for labor, not a quote for a recessed in-ceiling job.
The wider pool is home theater companies. 761 listed installers offer home theater work, and the 14 that publish prices have a median starting price of $3,000. These are the companies' own website claims. A combo build often needs two trades: a carpenter for the bulkhead or recess and an AV installer for the screen, projector and trigger. Ask anyone you compare on our installer directory which half they cover. Our home theater installation page shows who does the AV side, and a short quiz can match you with installers who do both.
The bottom line
A drop-down screen over a TV is a framing decision first and a gadget purchase second. In the five threads we read, the projector itself was almost never the problem. The trouble was the fabric touching the TV, waving in a draft, or hanging too high because nobody ordered enough black drop. In the oldest thread (Stereonet), none of ten posters ran a screen over their TV, and one called the idea overkill. With today's tensioned in-ceiling screens it isn't, provided you set the fabric line at least 4 inches past the TV's front, buy a tab-tensioned screen, put a receptacle and trigger cable in the ceiling void, and leave the housing serviceable. Decide it before the drywall goes up, or you will be cutting into a finished ceiling.
FAQ
Can I add a drop-down screen to a media wall that is already built?
Yes, but usually as a surface-mounted case on the ceiling or on stand-off brackets, because recessing it means opening the ceiling and adding blocking. You will also need a code-compliant power source near the case rather than a cord through the ceiling.
Will an ultra-short-throw projector work with a drop-down screen over my TV?
Only with a tensioned screen. Elite Screens recommends fixed-frame or tab-tension screens for UST projectors because their steep light angle exaggerates any wave in the fabric.
How far must the screen hang from the wall?
Measure to the front of the TV or soundbar, whichever sticks out more, and add at least 4 inches. In the forum builds we read, the fabric sat roughly 4 to 12 inches off the wall depending on TV depth.
Sources
- AVForums: Projector Screen Over TV (2020–2024) — L-brackets, ceiling mounting, edge curl and waves, short black border needing an extension
- AVForums: How far is the gap between the projection screen and a wall (2017) — 19 cm clearance case, "100mm or more", roll-under vs reverse-roll, pelmet plan, recessing between joists
- What Hi-Fi forum: Set-up advice, plasma + projector (2011) — 8 ft screen dropped through a plasterboard slot, 12V trigger, pre-wiring list, tab-tension advice
- HiFiVision: Pls suggest projection screen setup — screen about 12 in from wall and 4 in in front of TV, L-bracket margin, fan/AC flutter, extra masking for tall ceilings
- Stereonet: For those with projectors, where do you watch TV? — 0 of 10 posters running a screen over the TV; TV-on-rails alternative
- Elite Screens: Best screen for an ultra/short-throw projector — UST needs fixed-frame or tab-tension screen; waves more pronounced
- Elite Screens: Evanesce Tab-Tension B in-ceiling screen — above/below-ceiling install, 12V trigger, 98.4 in power cord, top black border not extendable
- Draper Access XL installation instructions (PDF) — recess must leave the bottom of the case unobstructed for service
- EC&M: Where can you not use flexible cords? — NEC 400.12 limits on cords through or concealed in walls and ceilings
- Soundcore: How far should a projector be from the screen — throw ratio definition; 120 in screen at about 12–18 ft for 1.5–2.0 ratios
- AV Solution Hub: Throw distance for a 120-inch screen — 104 in width × 1.5 = about 13 ft worked calculation