For built in electric fireplace framing, buy the exact fire first and frame to its manual. Rough openings are tight and differ by model. A Dimplex IgniteXL 60 leaves only 3/8 inch of play in width and height. A generic "frame it 1-1/2 to 2 inches bigger" rule gives four to five times that. Frame-first only works if you pick the model and download its manual before anyone cuts a stud.
Below, we compare the three ways people actually frame these openings. Fire-first means you buy the unit and frame to its spec sheet. Frame-first means you frame to a rule of thumb and shop later. Oversize plus trim means you frame large and cover the gap with a trim kit or surround.
At a glance
| Criterion | Fire-first (frame to the manual) | Frame-first (rule-of-thumb opening) | Oversize + trim kit/surround |
|---|---|---|---|
| Opening accuracy | Exact; margins as small as 3/8 in | Guesswork; 1-1/2 to 2 in oversize is common advice | Deliberately loose, gap hidden by trim |
| Wall depth risk | Known before framing (2x4 vs 2x6 vs bump-out) | High: many units need more than a 2x4's 3-1/2 in | Low if the trim kit is rated for your wall depth |
| Power location | Placed where the cut sheet says (left, right, top) | Often ends up behind the unit or on the wrong side | Same as fire-first, if the model is chosen |
| Test before boarding | Yes, the unit is on site | No, there's nothing to test yet | Yes |
| Vents and service access | Planned around the real vent and junction box | Unknown until the unit arrives | Easiest: a removable surround gives access |
| Look | Flush, finish runs to the glass | Depends on the luck of the fit | Visible trim frame |
| Rework if wrong | Rare | Reframe, re-board, often re-tile | Usually just a different trim |
Fit tolerance: why "about 1-1/2 inches bigger" is the costliest myth
Winner: fire-first.
Generic DIY guides suggest making the opening about 1-1/2 to 2 inches taller and wider than the unit. Compare that with what manufacturers actually print:
| Model (manual/spec sheet) | Unit size (W x H x D) | Rough opening (W x H x D) | Play in width / height |
|---|---|---|---|
| Dimplex IgniteXL 60 (XLF60) | 60-1/4 x 15-5/8 x 5-7/8 in | 60-5/8 x 16 in; 5-1/2 in (2x6) or 3-1/2 in (2x4 + trim kit) | 3/8 in / 3/8 in |
| Amantii Panorama BI-50-SLIM | 48-5/8 x 23-5/8 x 6-3/4 in | 50 x 25 x 7 in | 1-3/8 in / 1-3/8 in |
| Rule of thumb from DIY guides | any | unit + 1-1/2 to 2 in | 1-1/2 to 2 in |
We assembled that table from the Dimplex spec sheet and the Amantii BI-SLIM manual. It shows two different "60-inch" fires needing openings that differ by 9 inches in height (16 vs 25 inches). If you frame to the rule of thumb for the Dimplex, the opening is 1-1/8 to 1-5/8 inches too wide, so a flush 2x6 install shows a gap no drywall mud will hide. If you frame tight for one brand and later switch to the other, the fire won't go in at all.
Installer-facing guides name the reverse mistake too. Some contractors frame to the unit's outside dimensions instead of the cut-sheet rough opening, which leaves no room for the mounting flange.
Rule of thumb: Nominal width ("60-inch") tells you almost nothing about the hole. Frame only from the rough-opening line in your model's manual. Hold the real unit up to the framing before you fasten the last stud.
Wall depth: the 2x4 trap
Winner: fire-first, with oversize + trim a close second.
A 2x4 stud wall gives 3-1/2 inches of cavity. The Amantii BI-SLIM needs 7 inches, so it can't go in a plain 2x4 wall at all. It needs a bump-out or a media wall frame. The Dimplex XLF60 recesses flush in 2x6 framing (5-1/2 inches). It only fits a 2x4 wall with the optional XLFTRIM60 trim kit, a 62-3/4 x 18-1/4 inch frame that covers the edge where the fire stands proud. That is the oversize + trim strategy done properly: the trim is engineered for that exact depth, not improvised.
Dimplex also requires a bottom sill at least 3-1/2 inches deep, built to support the front of the unit so the power wires can run behind it. Dimplex recommends mounting the bottom of the unit 30 to 40 inches off the floor for flame viewing. Both details change your header and sill heights, which you can't set until you know the model.
Important: If the opening goes into a load-bearing wall, you need a properly sized header and temporary support while you cut. That's a carpenter's or structural engineer's call, not a guess.
For the stud-type debate behind the opening, see metal vs wood studs for a media wall frame.
Power in the right spot
Winner: fire-first. This is where frame-first fails most often.
Each manual puts the connection somewhere different:
- Amantii BI-SLIM: plug and hardwire junction block on the left side, behind a two-screw cover plate, with a 70-7/8 inch cord. The manual calls for a 15 amp, 120 volt grounded branch circuit.
- EcoSmart Motion built-ins: electrical connection at the top right of the rough-in framing.
- Dimplex XLF60: ships with a 120V plug-in cord kit, or hardwires to 120V (1,500 W, 5,718 BTU) or 240V (2,500 W, 8,530 BTU). A pass-through hole in the sill routes the wire.
A 1,500-watt heater draws 12.5 amps at 120 volts. Retailer and manufacturer guides agree it should not share a circuit with the TV and AV gear. The 120V-or-240V decision has to be made before the wall closes.
Homeowners argue most about putting the outlet behind the unit. In one Hearth.com thread on hiding an outlet behind a fireplace insert, we counted eight posters. Four raised heat (heat-rated receptacles, insulation, high-temperature cord sleeves). Three raised access or a disconnect: if a cheap receptacle fails behind a finished install, the unit has to come out. One of them suggested a switch in the room so the unit can be shut off for service, and later said that running the cord out the front is simpler.
Important: Hardwiring, a new dedicated circuit, or a 240V supply is work for a licensed electrician, and often needs a permit. Our separate guide covers what the NEC allows for outlets inside a media wall. Do not bury a junction box with no access.
Test before you board
Winner: fire-first and oversize + trim (tie). Frame-first can't do it.
The Amantii manual is explicit on this. First, pre-test the unit plugged into a grounded 120V outlet, checking the switches, remote and heater. Then, only "after checking that the fireplace operates properly," cover the glass and install the drywall or plywood. The trim kit only works if the finished wall is no thicker than 1 inch. Stacking tile and thinset on half-inch board can blow that limit.
Pro tip: Run every function, heater on high included, on the circuit it will actually live on before boarding. You'll find a dead fan or a tripping breaker while it's still a quick fix, not a tile demolition.
Vents and service access
Winner: oversize + trim kit.
Vent locations vary even within one brand. Amantii's Symmetry vents at the top front, while some of its other models discharge low on the front. Napoleon says its Allure series uses front vents specifically so the unit can be fully recessed. Framing, trim and décor must never block intakes or heat outlets. Retailer guidance also keeps the heat path at least 36 inches from drapes and furniture.
Service is the forgotten half. The Amantii manual says the heater must be serviced annually, depending on use, and its wiring sits behind a side cover plate. A removable surround (the Amantii one lifts off after two screws) or a planned access panel beats grinding out tile. For heat limits on the TV above, read our electric fire heat and ventilation rules.
What a wrong opening costs
Winner: fire-first, by a wide margin.
GetMediaWall's pricing model puts a 12–16 ft painted wall with a 60-inch electric fireplace at $7,100–$10,400 nationally ($9,200–$13,600 in the Bay Area). The 60-inch unit alone is $2,500 of that. The model prices tile at $28 per sq ft and stone at $45 per sq ft over paint.
Estimated cost: Here's a worked example. You tile 30 sq ft around a 60-inch fire, then discover the opening is 1/2 inch short. In our model that's about $840 of tile finish ($1,350 if it's stone) that has to come off and go back. Reframing and electrical changes come on top. The fix that costs nothing is reading the manual before the first cut.
If you're hiring out, 125 installers listed on GetMediaWall say they offer fireplace media wall installation. Only 19 publish a price, and the median advertised starting price is $189, which is clearly a starting fee, not a full build. Just 84 of the 1,009 listed companies state a warranty on their own websites, with a median of 12 months. Ask whether the warranty covers a refit if the opening is wrong. These are the companies' own claims; we don't verify them.
So which should you choose?
Best for: Fire-first suits nearly everyone building a new wall. Buy the unit, confirm it's rated for recessed installation, check the return window, then frame from the manual with the fire on site.
Best for: Frame-first only suits builders who must frame before the fire can be delivered. Even then, pick the exact model number and frame to its downloaded manual, never to a generic allowance.
Best for: Oversize + trim kit suits 2x4 walls, owners who may swap units later, and anyone who wants easy service access. Use the manufacturer's matching trim kit rather than a homemade frame.
Ready to plan it? Sketch the opening and TV spacing in the media wall configurator, then get matched with local installers and free quotes. If you're upgrading an existing wall, see what to do when a replacement electric fire won't fit.
Sources
- Dimplex IgniteXL 60 (XLF60) spec sheet — unit and framing dimensions, 2x4/2x6 depth, trim kit size, 3-1/2 in sill, 30–40 in mounting height, 120V/240V output
- Amantii BI-SLIM installation manual — BI-50/60-SLIM rough openings, unit size, left-side plug and junction block, 15 A 120 V circuit, pre-test and test-before-drywall steps, 1 in finish limit, annual service
- EcoSmart Fire: built-in framing, Motion electric fireplaces — model-specific rough openings, electrical at top right, 36 in from combustibles
- House Digest: DIY electric fireplace insert frame — the "1-1/2 to 2 inches taller and wider" rule of thumb
- Very Good Fireplaces: common electric fireplace installation failures — framing to outside dimensions, junction box placement, no service access
- The Everything Depot: electric fireplace installation mistakes — Amantii vent locations by model, service access, testing before finishing
- Fireplaces Direct: 5 common electric fireplace installation mistakes — 1,500 W / 12.5 A dedicated circuit, load-bearing header, 36 in clearance to furnishings
- Napoleon electric wall-mount brochure — Allure series front vents allow full recessing
- Hearth.com: Install electric outlet behind fireplace? — homeowner debate counted above: heat-rated parts, accessibility, in-room switch
- Direct Fireplaces: media wall fires planning guide — buy the fire first; resizing a stud wall is a major job